View TZY2R200AC01_9014494.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ceramic trimmer capacitors
t13e.pdf mar.12,2015 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. eu rohs compliant s !lltheproductsinthiscatalogcomplywith%52o(3 s %52o(3isthe%uropean$irective%5onthe2estrictionofthe5se of#ertain(azardous3ubstancesin%lectricaland%lectronic% quipment s for moredetailspleaserefe r t o our website 'muratags a pp ro a c hfo r%52o(3' httpwwwmuratacomen eusupportcompliancerohs
t13e.pdf mar.12,2015 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. contents please check the murata home page (http://www.murata.com/) if you cannot find the part number in the catalog. part numbering p2 selection guide of ceramic trimmer capacitors p3 packaging p26 recommended adjustment tools p28 qualified standards p29 product specifications are as of may 2014 . bluetoothr is a registered trademark or trademark of bluetooth sig, inc. in the united states and other countries. tzr1 series p4 1 tzy2 series p8 2 tzc3 series p13 3 tzw4 series p18 4 tzb4 series p21 5 1 2 3 4 5
t13e.pdf mar.12,2015 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 2 o part numbering (part number) qproduct id tz trimmer capacitors product id rmaximum capacitance expressed by three-digit alphanumerics. the unit is pico-farad (pf). the first and second figures are significant digits, and the third figure expresses the number of zeros that follow the two numbers. if there is a decimal point, it is expressed by the capital letter "r". in this case, all figures are significant digits. ceramic trimmer capacitors tterminal shape code terminal shape a b top adjustment: top adjustment: tzr1, tzy2, tzc3, tzw4, tzb4 tzb4 upackaging code b00 r00 r01* bulk reel (taping ?180mm) reel (taping ?330mm) packaging wseries/terminal code b4 w4 c3 y2 r1 4mm size smd type 4mm size smd type 3mm size smd type 2mm size smd type 1mm size smd type series/terminal etemperature characteristics code z r k p np0ppm/c n750ppm/c n1000ppm/c n1200ppm/c temperature characteristics please refer to dimensions for terminal details. * tzb4 only. yindividual specifications code 001 c01 110 a10 b10 tzr1, tzw4 standard type tzy2 standard type tzc3 standard type tzb4 no-cover film standard type tzb4 with cover film standard type individual specifications please refer to ratings for tolerance of temperature characteristics. t a y c01 q tz u r00 r 200 e r w y2
t13e.pdf mar.12,2015 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 3 selection guide of ceramic trimmer capacitors mounting method? all ceramic trimmer capacitor products comply with rohs and elv. surface mount height 0.90mm max. height 2.6mm max. height 1.7mm max. height 3.2mm max. tzc3 3.2(w) x 4.5(l) tzb4_aa 4.0(w) x 4.5(l) tzb4_bb 4.0(w) x 4.5(l) tzw4 4.2(w) x 5.2(l) tzb4_ab 4.0(w) x 4.5(l) (with cover film) tzb4_bb 4.0(w) x 4.5(l) (with cover film) tzr1 1.5(w) x 1.7(l) tzy2 2.5(w) x 3.2(l) height 3.2mm max. height 1.25mm max. flow reflow high frequency power
ceramic trimmer capacitors tzr1 series 0.35 0.9 max. 1.5 0.45 1.7 0.2 (depth;0.15) ( tolerance: 0.1 ) in mm part number c min. (max.) (pf) c max. (pf) tc q rated voltage withstanding voltage tzr1z010a001 0.55 1.0 +100/-0% np0300ppm/c 200min. at 200mhz, cmax. 25vdc 55vdc tzr1z1r5a001 0.7 1.5 +100/-0% np0300ppm/c 200min. at 200mhz, cmax. 25vdc 55vdc tzr1z040a001 1.5 4.0 +100/-0% np0500ppm/c 300min. at 1mhz, cmax. 25vdc 55vdc tzr1r080a001 3.0 8.0 +100/-0% n750500ppm/c 300min. at 1mhz, cmax. 25vdc 55vdc insulation resistance: 10000m ohm torque: 0.1 to 1.0mnm operating temperature range: -25 to +85c cover metal rotor monolithic stator c construction t13e.pdf mar.12,2015 4 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 1 c features 1. ultra-small and thin with external dimensions of 1.5(w)x1.7(l)x0.85(h)mm (80% less in volume than the current product). 2. unique construction with no plastic material provides superior soldering heat resistance to maintain excellent characteristic performance after re? ow soldering. 3. suitable for high frequency circuit due to high self-resonant frequency (6.2ghz of tzr1z010 at 1.0pf setting). c applications 1. bluetooth r 2. crystal oscillators 3. crystal ? lters 4. hand radios 5. miniature tuner packs (fm radio, tv) 6. remote keyless entry systems
8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z010 (np0300 ppm/c) temp.(c) cap.change (%) c temperature characteristics tzr1z010 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z1r5 (np0300 ppm/c) temp.(c) cap.change (%) tzr1z1r5 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z040 (np0500 ppm/c) temp.(c) cap.change (%) tzr1z040 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 r080 (n750500 ppm/c) temp.(c) cap.change (%) tzr1r080 10000 1000 100 10 1 0 0246 frequency (ghz) 0.55pf set 1.0pf set z010 q 810 c frequency characteristics tzr1z010 10000 1000 100 10 1 0 0246 frequency (ghz) 0.7pf set 1.5pf set z1r5 q 810 tzr1z1r5 1000 1000 100 10 q 1 10 100 500 1000 1500 2000 2500 frequency (mhz) capacitance (pf) z040 tzr1z040 1000 1000 100 10 q 1 10 100 500 1000 1500 2000 frequency (mhz) capacitance (pf) r080 tzr1r080 t13e.pdf mar.12,2015 5 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 1
2.2 1.2 0.5 tolerance: 0.1 in mm c land pattern temperature (c) t3 t2 t3 t2 t5 t4 t1 time (s) t1 reflow soldering profile qsoldering profile for lead-free solder (96.5sn/3ag/0.5cu) standard profile pre-heating heating peak temperature (t3) cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 2 times 2453c 150 to 180c 60 to 120sec. 220c 30 to 60sec. limit profile standard profile standard profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 1 time 230 +5/-0c 150c 60 to 120sec. 183c 30sec. limit profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t4) time (t3) 2 times 260 +5/-0c 150 to 180c 60 to 120sec. 230c 30 to 50sec. temperature (c) time (s) standard profile t1 t1 t2 t3 t2 wsoldering profile for eutectic solder (63sn/37pb) (limit profile: refer to q) soldering iron standard profile temperature of soldering iron tip soldering time soldering iron power output 35010c 3sec. max. 30w max. 1 time cycle of soldering iron peak temperature (t5) peak temperature (t3) c temperature pro le c notice (storage and operating conditions) t13e.pdf mar.12,2015 6 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 1 1. do not use the trimmer capacitor under atmosphere of rtv silicone rubber (room temperature vulcanizing silicone rubber) except acetone liberating silicone sealant. 2. before using trimmer capacitors, please store under the conditions of -10 to +40c and 30 to 85%rh. 3. do not store in or near corrosive gasses. 4. use within 6 months of delivery. 5. do not store under direct sunlight. 6. do not use the trimmer capacitor under the conditions listed below. (1) corrosive gasses atmosphere (ex. chlorine gas, hydrogen sul? de gas, ammonia gas, sulfuric acid gas, nitric oxide gas, etc.) (2) in liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) dusty / dirty atmosphere (4) direct sunlight (5) static voltage or electric/magnetic ? elds (6) direct sea breeze (7) other variations of the above
c notice (soldering and mounting) c notice (handling) c notice (other) before using trimmer capacitors, please test after assembly in your particular mass production system. t13e.pdf mar.12,2015 7 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 1 1. soldering (1) tzr1 series can be soldered by re? ow soldering method and soldering iron. do not use ? ow soldering method (dipping). (2) soldering conditions refer to the temperature pro? le. if the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the speci? ed characteristics. (3) the amount of solder is critical. (4) the thickness of solder paste should be printed from 100 micro m to 150 micro m and the dimension of land pattern should be murata's standard land pattern used at re? ow soldering. insuf? cient amounts of solder can lead to insuf? cient soldering strength on pcb. excessive amounts of solder may cause bridging between the terminals or contact failure due to ? ux wicking up. (5) when using soldering iron, the diameter of the string solder shall be less than 0.5mm. the string solder shall be applied to the lower part of the terminal only. do not apply ? ux except to the terminals. excessive amounts of solder and/or applying solder to the upper part of the terminal may cause ? xed metal rotor or contact failure due to ? ux invasion into the movable part and/or the contact point. the soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. if such contact does occur, the trimmer capacitor may be damaged. (6) our recommended chlorine content of solder is as follows. (a) solder paste: 0.2wt% max. (b) string solder: 0.5wt% max. (7) do not use water-soluble ? ux (for water cleaning). to prevent the deterioration of trimmer capacitor characteristics, apply ? ux only to terminals. 2. mounting (1) do not apply excessive force (preferably 5.0 n [ref: 500gf] max.), when the trimmer capacitor is mounted on the pcb. (2) do not warp and/or bend pcb to protect trimmer capacitor from breaking. (3) use a pick-up nozzle of a suitable dimension. (1.6mm external diameter and 0.8mm bore diameter.) 3. cleaning this product cannot be cleaned because of open construction. 4. other note the polarity of the trimmer capacitor to minimize in? uence by stray capacitance. (refer to the dimensions concerning the polarity.) 1. use suitable screwdrivers that ? t comfortably in driver slot. *recommended screwdriver for manual adjustment murata: kmdr160 2. when adjusting with a screwdriver, do not apply excessive force (preferably 0.5 n [ref: 50gf] max.) to minimize capacitance drift. excessive force applied to the screwdriver slot may cause deformation of the products. 3. do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. they may cause corrosion or electrical contact problems.
ceramic trimmer capacitors tzy2 series 3.20.2 2.50.2 1.25max. 0.95 1.0 0.45 0.5 1.4 ( tolerance: 0.1 ) in mm insulation resistance: 10000m ohm torque: 0.7 to 4.9mnm operating temperature range: -25 to +85c cover metal rotor monolithic stator c construction part number c min. (max.) (pf) c max. (pf) tc q rated voltage withstanding voltage tzy2z010ac01 0.6 1.0 +100/-0% np0300ppm/c 200min. at 200mhz, cmax. 25vdc 55vdc tzy2z2r5ac01 1.0 2.5 +100/-0% np0300ppm/c 200min. at 200mhz, cmax. 25vdc 55vdc tzy2z030ac01 1.5 3.0 +100/-0% np0300ppm/c 300min. at 1mhz, cmax. 25vdc 55vdc tzy2z060ac01 2.5 6.0 +100/-0% np0300ppm/c 500min. at 1mhz, cmax. 25vdc 55vdc tzy2z100ac01 3.0 10.0 +100/-0% np0300ppm/c 500min. at 1mhz, cmax. 25vdc 55vdc TZY2R200AC01 4.5 20.0 +100/-0% n750500ppm/c 500min. at 1mhz, cmax. 25vdc 55vdc tzy2r250ac01 5.5 25.0 +100/-0% n750500ppm/c 300min. at 1mhz, cmax. 25vdc 55vdc tzy2k450ac01 8.0 45.0 +100/-0% n1000500ppm/c 300min. at 1mhz, cmax. 25vdc 55vdc t13e.pdf mar.12,2015 8 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 2 c features 1. small and thin size with external dimensions of 2.5(w)x3.2(l)x1.25max.(h)mm. 2. new shape of cover can improve the ? ux invasion compared with current products. 3. improvement of the adhesion between rotor and stator leads to superior stability. 4. unique construction with no plastic material provides superior soldering heat resistance to maintain excellent characteristic performance after re? ow soldering. 5. suitable for high frequency circuit due to high self-resonant frequency (4.8ghz of tzy2z010 at 1.0pf setting). c applications 1. crystal oscillators 9. remote keyless entry systems 2. crystal ? lters 10. w-lan 3. stylus pen 11. radar detectors 4. cordless telephones 12. compact radios 5. phs 13. dvd 6. hand radios 14. burglarproof devices 7. cellular telephones 15. headphone stereos 8. watches
8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z010 (np0300 ppm/c) temp.(c) cap.change (%) c temperature characteristics tzy2z010 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z2r5 (np0300 ppm/c) temp.(c) cap.change (%) tzy2z2r5 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z030 (np0300 ppm/c) temp.(c) cap.change (%) tzy2z030 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z060 (np0300 ppm/c) temp.(c) cap.change (%) tzy2z060 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z100 (np0300 ppm/c) temp.(c) cap.change (%) tzy2z100 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 r200 (n750500 ppm/c) temp.(c) cap.change (%) tzy2r200 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 r250 (n750500 ppm/c) temp.(c) cap.change (%) tzy2r250 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 k450 (n1000500 ppm/c) temp.(c) cap.change (%) tzy2k450 t13e.pdf mar.12,2015 9 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 2
1000 100 1 10 0246 frequency (ghz) 0.5pf set 1.0pf set z010 8 q c frequency characteristics tzy2z010 z100 q 1000 100 200 600 400 800 1000 10 1 1000 100 10 frequency (mhz) capacitance (pf) tzy2z100 r200 q 1000 100 200 1000 600 800 400 10 1 1000 100 10 frequency (mhz) capacitance (pf) tzy2r200 1000 100 10 1 1000 100 10 200 q 400 600 800 capacitance (pf) frequency (mhz) k450 1000 100 10 1 1000 100 10 200 q 400 600 800 capacitance (pf) frequency (mhz) k450 tzy2k450 tolerance: 0.1 in mm 4.0 2.4 1.2 c land pattern t13e.pdf mar.12,2015 10 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 2
temperature (c) t3 t2 t3 t2 t5 t4 t1 time (s) t1 reflow soldering profile qsoldering profile for lead-free solder (96.5sn/3ag/0.5cu) standard profile pre-heating heating peak temperature (t3) cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 2 times 2453c 150 to 180c 60 to 120sec. 220c 30 to 60sec. limit profile standard profile standard profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 1 time 230 +5/-0c 150c 60 to 120sec. 183c 30sec. limit profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t4) time (t3) 2 times 260 +5/-0c 150 to 180c 60 to 120sec. 230c 30 to 50sec. temperature (c) time (s) standard profile t1 t1 t2 t3 t2 wsoldering profile for eutectic solder (63sn/37pb) (limit profile: refer to q) soldering iron standard profile temperature of soldering iron tip soldering time soldering iron power output 35010c 3sec. max. 30w max. 1 time cycle of soldering iron peak temperature (t5) peak temperature (t3) c temperature pro le c notice (storage and operating conditions) t13e.pdf mar.12,2015 11 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 2 1. do not use the trimmer capacitor under atmosphere of rtv silicone rubber (room temperature vulcanizing silicone rubber) except acetone liberating silicone sealant. 2. before using trimmer capacitors, please store under the conditions of -10 to +40c and 30 to 85%rh. 3. do not store in or near corrosive gasses. 4. use within 6 months of delivery. 5. do not store under direct sunlight. 6. do not use the trimmer capacitor under the conditions listed below. (1) corrosive gasses atmosphere (ex. chlorine gas, hydrogen sul? de gas, ammonia gas, sulfuric acid gas, nitric oxide gas, etc.) (2) in liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) dusty / dirty atmosphere (4) direct sunlight (5) static voltage or electric/magnetic ? elds (6) direct sea breeze (7) other variations of the above
c notice (soldering and mounting) c notice (handling) c notice (other) before using trimmer capacitor, please test after assembly in your particular mass production system. t13e.pdf mar.12,2015 12 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 2 1. soldering (1) tzy2 series can be soldered by re? ow soldering method and soldering iron. do not use ? ow soldering method (dipping). (2) soldering conditions refer to the temperature pro? le. if the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the speci? ed characteristics. (3) the amount of solder is critical. (4) the thickness of solder paste should be printed from 120 micro m to 170 micro m and the dimension of land pattern should be murata's standard land pattern used at re? ow soldering. insuf? cient amounts of solder can lead to insuf? cient soldering strength on pcb. excessive amounts of solder may cause bridging between the terminals or contact failure due to ? ux wicking up. (5) when using soldering iron, the diameter of the string solder shall be less than 0.5mm. the string solder shall be applied to the lower part of the terminal only. do not apply ? ux except to the terminals. excessive amounts of solder and/or applying solder to the upper part of the terminal may cause ? xed metal rotor or contact failure due to ? ux invasion into the movable part and/or the contact point. the soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. if such contact does occur, the trimmer capacitor may be damaged. (6) our recommended chlorine content of solder is as follows. (a) solder paste: 0.2wt% max. (b) string solder: 0.5wt% max. (7) do not use water-soluble ? ux (for water cleaning). to prevent the deterioration of trimmer capacitor characteristics, apply ? ux only to terminals. 2. mounting (1) do not apply excessive force (preferably 5.0 n [ref: 500gf] max.), when the trimmer capacitor is mounted on the pcb. (2) do not warp and/or bend pcb to protect trimmer capacitor from breakage. (3) use a pick-up nozzle of a suitable dimension. (2.5mm external diameter and 1.2mm bore diameter.) 3. cleaning this product cannot be cleaned because of open construction. 4. other note the polarity of the trimmer capacitor to minimize in? uence by stray capacitance. (refer to the dimensions concerning the polarity.) 1. use suitable screwdrivers that ? t comfortably in driver slot. (1) recommended screwdriver for manual adjustment murata: kmdr060 (2) recommended screwdriver bit for automatic adjustment murata: kmbt060 2. when adjusting with a screwdriver, do not apply excessive force (preferably 1.0 n [ref: 100gf] max.) to minimize capacitance drift. excessive force applied to the screwdriver slot may cause deformation of the products. 3. do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. they may cause corrosion or electrical contact problems.
ceramic trimmer capacitors tzc3 series tolerance: 0.1 in mm 0.75 0.5 0.6 0.6 2.5 dia. 4.5 0.8 0.35 3.2 1.6 part number c min. (max.) (pf) c max. (pf) tc q rated voltage withstanding voltage stator/case color tzc3z030a110 1.4 3.0 +50/-0% np0300ppm/c 300min. at 1mhz, cmax. 100vdc 220vdc brown tzc3z060a110 2.0 6.0 +50/-0% np0300ppm/c 500min. at 1mhz, cmax. 100vdc 220vdc blue tzc3r100a110 3.0 10.0 +50/-0% n750300ppm/c 500min. at 1mhz, cmax. 100vdc 220vdc white tzc3p200a110 5.0 20.0 +50/-0% n1200500ppm/c 300min. at 1mhz, cmax. 100vdc 220vdc red tzc3p300a110 6.5 30.0 +50/-0% n1200500ppm/c 300min. at 1mhz, cmax. 100vdc 220vdc green insulation resistance: 10000m ohm torque: 1.5 to 9.8mnm operating temperature range: -25 to +85c center axis rotor spring terminal ceramic plate stator (one molded injection with stator terminal) stator terminal c construction c features 1. small size with external dimension of 3.2(w)x4.5(l)x1.6(h)mm. 2. color coded stator permits easy identi? cation of capacitance and reduces mounting errors. 3. can be adjusted with conventional adjustment tools having a thickness of 0.5mm. 4. designed for automatic placement in surface mount applications. 5. heat resistant resin withstands re? ow soldering temperatures. c applications 1. compact radios 2. headphones 3. stylus pen 4. portable radio equipment 5. hybrid ics 6. cellular telephones 7. cordless telephones 8. remote keyless entry systems t13e.pdf mar.12,2015 13 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 3
8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z030 (np0300 ppm/c) temp.(c) cap.change (%) c temperature characteristics tzc3z030 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z060 (np0300 ppm/c) temp.(c) cap.change (%) tzc3z060 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 r100 (n750300 ppm/c) temp.(c) cap.change (%) tzc3r100 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 p200 (n1200500 ppm/c) temp.(c) cap.change (%) tzc3p200 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 p300 (n1200500 ppm/c) temp.(c) cap.change (%) tzc3p300 t13e.pdf mar.12,2015 14 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 3
z030 1000 100 q 100 500 1000 1500 frequency (mhz) 2000 10 1 1000 100 10 capacitance (pf) c frequency characteristics tzc3z030 z060 q 1000 100 100 500 2000 1500 1000 frequency (mhz) 10 1 1000 100 10 capacitance (pf) tzc3z060 r100 q 1000 100 200 600 400 800 1000 frequency (mhz) 10 1 1000 100 10 capacitance (pf) tzc3r100 p200 q 1000 100 200 1000 600 800 400 frequency (mhz) 10 1 1000 100 10 capacitance (pf) tzc3p200 5.0 +0 C0.5 3.30.1 1.00.1 tolerance: 0.1 in mm c land pattern t13e.pdf mar.12,2015 15 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 3
temperature (c) t3 t2 t3 t2 t5 t4 t1 time (s) t1 reflow soldering profile qsoldering profile for lead-free solder (96.5sn/3ag/0.5cu) standard profile pre-heating heating peak temperature (t3) cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 2 times 2453c 150 to 180c 60 to 120sec. 220c 30 to 60sec. limit profile standard profile standard profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 1 time 230 +5/-0c 150c 60 to 120sec. 183c 30sec. limit profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t4) time (t3) 2 times 260 +5/-0c 150 to 180c 60 to 120sec. 230c 30 to 50sec. temperature (c) time (s) standard profile t1 t1 t2 t3 t2 wsoldering profile for eutectic solder (63sn/37pb) (limit profile: refer to q) soldering iron standard profile temperature of soldering iron tip soldering time soldering iron power output 35010c 3sec. max. 30w max. 1 time cycle of soldering iron peak temperature (t5) peak temperature (t3) c temperature pro le c notice (storage and operating conditions) t13e.pdf mar.12,2015 16 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 3 1. do not use the trimmer capacitor under atmosphere of rtv silicone rubber (room temperature vulcanizing silicone rubber) except acetone liberating silicone sealant. 2. before using trimmer capacitors, please store under the conditions of -10 to +40c and 30 to 85%rh. 3. do not store in or near corrosive gasses. 4. use within 6 months of delivery. 5. do not store under direct sunlight. 6. do not use the trimmer capacitor under the conditions listed below. (1) corrosive gasses atmosphere (ex. chlorine gas, hydrogen sul? de gas, ammonia gas, sulfuric acid gas, nitric oxide gas, etc.) (2) in liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) dusty / dirty atmosphere (4) direct sunlight (5) static voltage or electric/magnetic ? elds (6) direct sea breeze (7) other variations of the above
c notice (soldering and mounting) c notice (handling) c notice (other) before using trimmer capacitors, please test after assembly in your particular mass production system. t13e.pdf mar.12,2015 17 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 3 1. soldering (1) tzc3 series can be soldered by re? ow soldering method and soldering iron. do not use ? ow soldering method (dipping). (2) soldering conditions refer to the temperature pro? le. if the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the speci? ed characteristics. (3) the amount of solder is critical. (4) the thickness of solder paste should be printed from 150 micro m to 200 micro m and the dimension of land pattern should be murata's standard land pattern used at re? ow soldering. insuf? cient amounts of solder can lead to insuf? cient soldering strength on pcb. excessive amounts of solder may cause bridging between the terminals or contact failure due to ? ux wicking up. (5) when using soldering iron, the diameter of the string solder shall be less than 0.5mm. the string solder shall be applied to the lower part of the terminal only. do not apply ? ux except to the terminals. excessive amounts of solder and/or applying solder to the upper part of the terminal may cause ? xed metal rotor or contact failure due to ? ux invasion into the movable part and/or the contact point. the soldering iron should not come in contact with the stator of the trimmer capacitor. if such contact does occur, the trimmer capacitor may be damaged. (6) our recommended chlorine content of solder is as follows. (a) solder paste: 0.2wt% max. (b) string solder: 0.5wt% max. (7) do not use water-soluble ? ux (for water cleaning). to prevent the deterioration of trimmer capacitor characteristics, apply ? ux only to terminals. (8) when soldering the tzc3 series, the solder should not ? ow into the staking part of the substrate. if such ? ow does occur, driver slot rotation will be damaged. 2. mounting (1) do not apply excessive force (preferably 5.0 n [ref: 500gf] max.), when the trimmer capacitor is mounted on the pcb. (2) do not warp and/or bend pcb to protect trimmer capacitor from breakage. (3) use a pick-up nozzle of a suitable dimension. (2.5mm external diameter and 1.5mm bore diameter.) 3. cleaning this product cannot be cleaned because of open construction. 4. other note the polarity of the trimmer capacitor to minimize in? uence by stray capacitance. (refer to the dimensions concerning the polarity.) 1. use suitable screwdrivers that ? t comfortably in driver slot. (1) recommended screwdriver for manual adjustment standard type --> murata: kmdr010 (2) recommended screwdriver bit for automatic adjustment standard type --> murata: kmbt010 2. when adjusting with a screwdriver, do not apply excessive force (preferably 1.0 n [ref: 100gf] max.) to minimize capacitance drift. excessive force applied to the screwdriver slot may cause deformation of the products. 3. do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. they may cause corrosion or electrical contact problems.
ceramic trimmer capacitors tzw4 series 5.20.2 4.20.2 2.80.2 2.6 max. ( tolerance: 0.1 ) in mm 0.6 +0.1 -0.2 0.3 1.6 0.4 depth 3.0 2.2 part number c min. (max.) (pf) c max. (pf) tc q rated voltage withstanding voltage tzw4z010a001 0.4 1.0 +50/-0% np0150ppm/c 200min. at 500mhz, cmax. 250vdc 550vdc tzw4z1r5a001 0.4 1.5 +100/-0% np0150ppm/c 200min. at 500mhz, cmax. 250vdc 550vdc insulation resistance: 10000m ohm torque: 1.5 to 10.0mnm operating temperature range: -55 to +125c cover metal rotor monolithic stator c construction c features 1. to meet high power application due to withstanding voltage 550vdc. 2. extremely high self-resonant frequency. (more than 3ghz at rated c max.) 3. typical application: impedance matching for cellular base station. 4. high q value in more than vhf, uhf and microwave bands. (more than 200 in 500mhz, c max.) 5. available for pick and place machine. possible thinner design due to 2.6mm low pro? le. 6. non-electrical contact construction (rotor as middle electrode) provides high reliability. 7. compact size: 4.2(w)x5.2(l)x2.6max.(h)mm. c applications 1. transmitting power ampli? er for cellular base station 2. transmitting ampli? er for phs base station 3. high frequency electric circuit 4. high power radio transmission 5. transponder ampli? er for cable tv t13e.pdf mar.12,2015 18 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 4
8 6 4 2 20 C55 125 C2 C4 C6 C8 C10 C12 z010 (np0150 ppm/c) temp.(c) cap.change (%) c temperature characteristics tzw4z010 8 6 4 2 20 C55 125 C2 C4 C6 C8 C10 C12 z1r5 (np0300 ppm/c) temp.(c) cap.change (%) tzw4z1r5 z1r5 1000 100 q 500 1000 1500 2000 2500 3000 10 1 frequency (mhz) 1.5pf set c frequency characteristics tzw4z1r5 tolerance: 0.1 in mm 4.4 7.0 2.5 c land pattern temperature (c) t3 t2 t3 t2 t5 t4 t1 time (s) t1 reflow soldering profile qsoldering profile for lead-free solder (96.5sn/3ag/0.5cu) standard profile pre-heating heating peak temperature (t3) cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 2 times 2453c 150 to 180c 60 to 120sec. 220c 30 to 60sec. limit profile standard profile standard profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 1 time 230 +5/-0c 150c 60 to 120sec. 183c 30sec. limit profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t4) time (t3) 2 times 260 +5/-0c 150 to 180c 60 to 120sec. 230c 30 to 50sec. temperature (c) time (s) standard profile t1 t1 t2 t3 t2 wsoldering profile for eutectic solder (63sn/37pb) (limit profile: refer to q) soldering iron standard profile temperature of soldering iron tip soldering time soldering iron power output 35010c 3sec. max. 30w max. 1 time cycle of soldering iron peak temperature (t5) peak temperature (t3) c temperature pro le t13e.pdf mar.12,2015 19 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 4
c notice (storage and operating conditions) c notice (soldering and mounting) 1. soldering (1) tzw4 series can be soldered by re? ow soldering method and soldering iron. do not use ? ow soldering method (dipping). (2) soldering conditions refer to the temperature pro? le. if the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the speci? ed characteristics. (3) the amount of solder is critical. (4) the thickness of solder paste should be printed from 150 micro m to 200 micro m and the dimension of land pattern should be murata's standard land pattern used at re? ow soldering. insuf? cient amounts of solder can lead to insuf? cient soldering strength on pcb. excessive amounts of solder may cause bridging between the terminals or contact failure due to ? ux wicking up. (5) when using soldering iron, the diameter of the string solder shall be less than 0.5mm. the string solder shall be applied to the lower part of the terminal only. do not apply ? ux except to the terminals. excessive amounts of solder and/or applying solder to the upper part of the terminal may cause ? xed metal rotor or the contact failure due to ? ux invasion into the movable part and/or the contact point. the soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. if such contact does occur, the trimmer capacitor may be damaged. (6) our recommended chlorine content of solder is as follows. (a) solder paste: 0.2wt% max. (b) string solder: 0.5wt% max. (7) do not use water-soluble ? ux (for water cleaning). to prevent the deterioration of trimmer capacitor characteristics, apply ? ux only to terminals. 2. mounting (1) do not apply excessive force (preferably 5.0 n [ref: 500gf] max.), when the trimmer capacitor is mounted on the pcb. (2) do not warp and/or bend pcb to protect trimmer capacitor from breaking. (3) use a pick-up nozzle of a suitable dimension. (4.0mm external diameter and 1.2mm bore diameter.) 3. cleaning this product cannot be cleaned because of open construction. c notice (handling) c notice (other) before using trimmer capacitors, please test after assembly in your particular mass production system. t13e.pdf mar.12,2015 20 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 4 1. do not use the trimmer capacitor under atmosphere of rtv silicone rubber (room temperature vulcanizing silicone rubber) except acetone liberating silicone sealant. 2. before using trimmer capacitors, please store under the conditions of -10 to +40c and 30 to 85%rh. 3. do not store in or near corrosive gasses. 4. use within 6 months of delivery. 5. do not store under direct sunlight. 6. do not use the trimmer capacitor under the conditions listed below. (1) corrosive gasses atmosphere (ex. chlorine gas, hydrogen sul? de gas, ammonia gas, sulfuric acid gas, nitric oxide gas, etc.) (2) in liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) dusty/dirty atmosphere (4) direct sunlight (5) static voltage or electric/magnetic ? elds (6) direct sea breeze (7) other variations of the above 1. use suitable screwdrivers that ? t comfortably in driver slot. -recommended screwdriver for manual adjustment vessel : no.9000 -1.3x30 (murata p/n is kmdr130) 2. when adjusting with a screwdriver, do not apply excessive force (preferably 1.0 n [ref: 100gf] max.) to minimize capacitance drift. excessive force applied to the screwdriver slot may cause deformation of the products. 3. do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. they may cause corrosion or electrical contact problems.
ceramic trimmer capacitors tzb4 series 0.60.1 depth 0.5 1.40.1 dia. 2.70.3 2.40.1 4.00.2 4.50.2 5.0 1.20.1 3.00.2 tolerance: 0.5 in mm a type 0.60.1 depth 0.5 1.40.1 dia. 2.40.1 4.00.2 4.50.2 7.0 1.20.1 3.00.2 tolerance: 0.5 in mm b type part number c min. (max.) (pf) c max. (pf) tc q rated voltage withstanding voltage stator/case color tzb4z030 pp 10 1.4 3.0 +50/-0% np0200ppm/c 300min. at 1mhz, cmax 100vdc 220vdc brown tzb4z060 pp 10 2.0 6.0 +50/-0% np0200ppm/c 500min. at 1mhz, cmax. 100vdc 220vdc blue tzb4z100 pp 10 3.0 10.0 +50/-0% np0300ppm/c 500min. at 1mhz, cmax. 100vdc 220vdc white tzb4r200 pp 10 4.5 20.0 +50/-0% n750400ppm/c 500min. at 1mhz, cmax 100vdc 220vdc red tzb4p300 pp 10 6.5 30.0 +50/-0% n1200500ppm/c 300min. at 1mhz, cmax 100vdc 220vdc green tzb4p400 pp 10 8.5 40.0 +50/-0% n1200500ppm/c 300min. at 1mhz, cmax 100vdc 220vdc yellow tzb4z250 pp 10 4.0 25.0 +100/-0% np0300ppm/c 300min. at 1mhz, cmax. 50vdc 110vdc black+marking tzb4r500 pp 10 7.0 50.0 +100/-0% n750300ppm/c 300min. at 1mhz, cmax 50vdc 110vdc black+marking c features 1. miniature rectangular shape: 4.0(w)x4.5(l)x3.0(h)mm. 2. color coded case facilitates identi? cation of capacitance range. 3. designed for automatic placement in surface mount applications. 4. designed to withstand ? ux baths and solder baths (with cover ? lm type). 5. can be temporarily attached to pcb with adhesives (terminal style a and b). 6. can be re? ow and ? ow (with cover ? lm type) soldering method. 7. stable characteristics over a wide frequency range. (resonant frequency: 1000mhz min. / 6pf) c applications 1. car audio systems 2. cordless telephones 3. hybrid ics 4. remote keyless entry systems 5. tuner packs 6. surveillance cameras 7. dvd 8. burglarproof devices 9. entry phone t13e.pdf mar.12,2015 21 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 5 insulation resistance: 10000m ohm torque: 1.5 to 9.8mnm operating temperature range: -25 to +85c first blank: terminal type second blank: cover ? lm codes (a: not provided, b: provided) rex. tzb4z100a b10: terminal type is a, and cover ? lm is provided. plastic case rotor spring metal rotor ceramic plate stator terminal cover film (cover film type) rotor terminal C + c construction
1.60.1 7.0 +0 - 0.5 2.40.2 (in mm) c land pattern/mounting holes a type (in mm) 4.00.2 1.60.1 8.0 +0 - 0.5 b type 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z030 (np0200 ppm/c) temp.(c) cap.change (%) c temperature characteristics tzb4z030 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z060 (np0200 ppm/c) temp.(c) cap.change (%) tzb4z060 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z100 (np0300 ppm/c) temp.(c) cap.change (%) tzb4z100 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 r200 (n750400 ppm/c) temp.(c) cap.change (%) tzb4r200 continued on the following page. t13e.pdf mar.12,2015 22 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 5 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 p300 (n1200500 ppm/c) temp.(c) cap.change (%) tzb4p300 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 p400 (n1200500 ppm/c) temp.(c) cap.change (%) tzb4p400
continued from the preceding page. c temperature characteristics 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 z250 (np0300 ppm/c) temp.(c) cap.change (%) tzb4z250 8 6 4 2 20 C25 85 C2 C4 C6 C8 C10 C12 r500 (n750300 ppm/c) temp.(c) cap.change (%) tzb4r500 z060 1000 100 q 10 1000 100 10 800700600500400300200100 900 1000 frequency (mhz) 1 capacitance (pf) c frequency characteristics tzb4z060 z100 q 1000 100 800700600500400300200100 900 1000 frequency (mhz) 10 1 1000 100 10 capacitance (pf) tzb4z100 t13e.pdf mar.12,2015 23 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 5 r200 q 1000 100 200 100 400 300 500 600 frequency (mhz) 10 1 1000 100 10 capacitance (pf) tzb4r200 r500 q 1000 100 100 500 300 400 200 frequency (mhz) 10 1 1000 100 10 capacitance (pf) tzb4r500
temperature (c) t3 t2 t3 t2 t5 t4 t1 time (s) t1 soldering profile for lead-free solder (96.5sn/3ag/0.5cu), eutectic solder (63sn/37pb) temperature (c) t1 t2 t3 t2 t1 time (s) limit profile standard profile qsoldering profile for lead-free solder (96.5sn/3ag/0.5cu) limit profile standard profile s!vailableforterminalshape!"and% s)mmersethebodyinsolderbathavailableforcoverfilmtype standard profile pre-heating heating temp. (t1) time (t1) temp. (t2) time (t2) 1 time 150c 60 to 120sec. 250c 5sec. max. temperature (c) time (s) standard profile t1 t1 t2 t3 t2 wsoldering profile for eutectic solder (63sn/37pb) (limit profile: refer to q) flow soldering profile reflow soldering profile cycle of reflow limit profile pre-heating heating temp. (t1) time (t1) temp. (t3) time (t2) 2 times 150c 60 to 120sec. 2653c 5sec. max. cycle of reflow standard profile pre-heating heating peak temperature (t3) cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 2 times 2453c 150 to 180c 60 to 120sec. 220c 30 to 60sec. limit profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t4) time (t3) 2 times 260 +5/-0c 150 to 180c 60 to 120sec. 230c 30 to 50sec. peak temperature (t5) standard profile pre-heating heating cycle of reflow temp. (t1) time (t1) temp. (t2) time (t2) 1 time 230 +5/-0c 150c 60 to 120sec. 183c 30sec. peak temperature (t3) soldering iron standard profile temperature of soldering iron tip soldering time soldering iron power output 35010c 3sec. max. 30w max. 1 time cycle of soldering iron c temperature pro le c notice (storage and operating conditions) t13e.pdf mar.12,2015 24 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 5 1. do not use the trimmer capacitor under atmosphere of rtv silicone rubber (room temperature vulcanizing silicone rubber) except acetone liberating silicone sealant. 2. before using trimmer capacitors, please store under the conditions of -10 to +40c and 30 to 85%rh. 3. do not store in or near corrosive gasses. 4. use within 6 months of delivery. 5. do not store under direct sunlight. 6. do not use the trimmer capacitor under the conditions listed below. (1) corrosive gasses atmosphere (ex. chlorine gas, hydrogen sul? de gas, ammonia gas, sulfuric acid gas, nitric oxide gas, etc.) (2) in liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) dusty / dirty atmosphere (4) direct sunlight (5) static voltage or electric/magnetic ? elds (6) direct sea breeze (7) other variations of the above
c notice (soldering and mounting) c notice (handling) 1. use suitable screwdrivers that ? t comfortably in driver slot. (1) recommended screwdriver for manual adjustment murata: kmdr010 (2) recommended screwdriver bit for automatic adjustment murata: kmbt010 2. when adjusting with a screwdriver, do not apply excessive force (preferably 1.0 n [ref: 100gf] max.) to minimize capacitance drift. excessive force applied to the screwdriver slot may cause deformation of the products. 3. do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. they may cause corrosion or electrical contact problems. 4. do not break the cover ? lm before the completion of pcb mounting, soldering, and cleaning. 5. do not clean the trimmer capacitor after the cover ? lm has been broken. 6. to break the cover ? lm, ? rst turn the screwdriver more than 360, and set the capacitance value. (inserting the screwdriver only will not break the cover ? lm.) c notice (other) before using trimmer capacitors, please test after assembly in your particular mass production system. t13e.pdf mar.12,2015 25 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 5 1. soldering (1) can be soldered by re? ow soldering method, ? ow soldering method, and soldering iron. (2) soldering conditions refer to the temperature pro? le. if the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the speci? ed characteristics. (3) the amount of solder is critical. (4) the thickness of solder paste should be printed from 150 micro m to 200 micro m and the dimension of land pattern should be murata's standard land pattern used at re? ow soldering. insuf? cient amounts of solder can lead to insuf? cient soldering strength on pcb. excessive amounts of solder may cause bridging between the terminals or contact failure due to ? ux wicking up. (5) when using soldering iron, the string solder shall be applied to the lower part of the terminal only. do not apply ? ux except to the terminals. excessive amounts of solder and/or applying solder to the upper part of the terminal may cause ? xed rotor or contact failure due to ? ux invasion into the movable part and/or the contact point. the soldering iron should not come in contact with the plastic case of the trimmer capacitor. if such contact does occur, the trimmer capacitor may be damaged. (6) our recommended chlorine content of solder is as follows. (a) solder paste: 0.2wt% max. (b) string solder: 0.5wt% max. (7) do not use water-soluble ? ux (for water cleaning). to prevent the deterioration of trimmer capacitor characteristics, apply ? ux only to terminals. 2. mounting (1) do not apply excessive force (preferably 5.0n [ref: 500gf] max.), when the trimmer capacitor is mounted on the pcb. (2) do not warp and/or bend pcb to protect trimmer capacitor from breakage. (3) when bending the terminals, do not apply excessive force to the body of the product to protect the terminal ? xing part from damage. (4) use a pick-up nozzle of a suitable dimension. > without cover ? lm type - external dimensions of 4.5x4.0mm and 2.5mm bore diameter. > with cover ? lm type - 4.0mm external diameter and 2.0mm bore diameter. 3. cleaning [with cover ? lm type] isopropyl alcohol and ethyl alcohol are available material for cleaning. if you use any other type of solvent, please evaluate performance in your application. moreover, please con? rm that no damage has occurred to the trimmer capacitor after cleaning in your conditions. 4. other note the polarity of the trimmer capacitor to minimize in? uence by stray capacitance. (refer to the dimensions concerning the polarity.)
packaging part number tzr1 tzy2 tzc3 tzw4 tzb4 3000 2000 1000 500 500 ?180mm reel - - - - 2500 ?330mm reel 500 500 500 100 500 bulk minimum quantity (pcs.) c minimum quantity 4.00.1 8.00.3 2.00.1 4.00.1 1.5 dia. +0.1 -0 2.00.2 1.750.1 3.50.1 1.80.2 1.050.2 0.250.1 (in mm) c tape dimensions tzr1 series 1.5 +0.1 C 0 dia. 2.0 4.0 a a 2.70.2 4.0 3.5 0.25 t 8.00.2 1.75 a-across section t=tzy2 (tzvy2) : 1.60.2 3.60.2 tolerance: 0.1 in mm tzy2 series 1.5 +0.1 C 0 dia. 4.90.2 a 2 8 4 5.5 1.75 120.3 0.3 2.00.2 a a-across section tolerance : 0.1 in mm 3.60.2 tzc3 series 120.2 1.5 +0.1 C 0 dia. 5.6 a 2 8 4 5.5 1.75 0.3 2.6 a a-across section tolerance: 0.1 in mm 4.6 tzw4 series 1.5 +0.1 C 0 dia. 8.0 2.0 4 .0 a a 1.8 4.3 3.550.2 4.8 7.5 5.5 12.00.3 0.30.1 a-across section direction of feed tolerance: 0.1 in mm 1.75 tzb4 series continued on the following page. t13e.pdf mar.12,2015 26 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering.
packaging continued from the preceding page. (in mm) 13.00.5 dia. 21.00.8 dia. 2.00.5 1782 dia. 9.01.0 50 min. 13.01.0 c reel dimensions (180mm diameter) tzr1/tzy2 series (in mm) 13.00.5 dia. 21.00.8 dia. 2.00.5 1782 dia. 13.01.0 50 min. 17.01.0 tzc3/tzw4/tzb4 series (in mm) 13.00.5 dia. 21.00.8 dia. 2.00.5 3282 dia. 13.51.0 50 min. 17.51.0 c reel dimensions (330mm diameter) tzb4 series t13e.pdf mar.12,2015 27 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering.
recommended adjustment tools c for manual adjustment series murata model number manufacturers model number shape tzr1 tzy2 tzc3 tzb4 tzw4 kmdr160 kmdr060 kmdr010 kmdr130 murata mfg. kmdr160 engineer inc. da-89 murata mfg. kmdr010 vessel mfg. no.9000 -1.3g30 please use the following recommended screwdrivers. you can order these drivers using the part numbers below. although you can also adjust the capacitance value using commercial products, please use one with the same head size as the driver listed below. 1.5 80 bit shape: minus (0.3x0.13) (in mm) 18 108 (in mm) bit shape: minus (0.8x0.35) (in mm) 50 122 20 bit shape: minus (2.2x0.4) (in mm) 125 15 9000 1.3-30 ceramic blade electronics bit shape: minus (1.3x30) c for automatic adjustment tzy2 tzc3 tzb4 kmbt060 kmbt010 murata mfg. kmbt060 murata mfg. kmbt010 series murata model number manufacturers model number shape (in mm) 25 2.4 dia. 0.6 bit shape: minus (0.56x0.25) (in mm) 30 2.2 dia. bit shape: minus (2.2x0.4) t13e.pdf mar.12,2015 28 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering.
t13e.pdf mar.12,2015 ! note ? please read rating and ! caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. ? this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 29 qualified standards murata factory sabae murata mfg. co., ltd. the products listed herein have been produced by a iso9001 certified factory. ? no odcs (ozone depleting chemicals) are used on any murata trimmer capacitors.
murata manufacturing co., ltd. www.murata.com note 1 export control for customers outside japan: no murata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or otherwise contribution to (1) any weapons (weapons of mass destruction [nuclear, chemical or biological weapons or missiles] or conventional weapons) or (2) goods or systems specially designed or intended for military end-use or utilization by military end-users. for customers in japan: for products which are controlled items subject to the foreign exchange and foreign trade law of japan, the export license speci? ed by the law is required for export. 2 please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage a third partys life, body or property, or when one of our products is intended for use in applications other than those specified in this catalog. 1 aircraft equipment 2 aerospace equipment 3 undersea equipment 4 power plant equipment 5 medical equipment 6 transportation equipment (vehicles, trains, ships, etc.) 7 traffi c signal equipment 8 disaster prevention / crime prevention equipment 9 data-processing equipment 10 application of similar complexity and/or reliability requirements to the applications listed above 3 product speci? cations in this catalog are as of may 2014. they are subject to change or our products in it may be discontinued without advance notice. please check with our sales representatives or product engineers before ordering. if there are any questions, please contact our sales representatives or product engineers. 4 please read rating and caution (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. 5 this catalog has only typical speci? cations. therefore, please approve our product speci? cations or transact the approval sheet for product speci? cations before ordering. 6 please note that unless otherwise speci? ed, we shall assume no responsibility whatsoever for any con? ict or dispute that may occur in connection with the eff ect of our and/or a third partys intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our catalogs. in this connection, no representation shall be made to the eff ect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 7 no ozone depleting substances (ods) under the montreal protocol are used in our manufacturing process. global locations for details please visit www.murata.com cat. no. t13e-16

▲Up To Search▲

Price & Availability of TZY2R200AC01

	To Download TZY2R200AC01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .